Railenergy

GLOSSARY

TermDescription
(Traction) generatorDevice which converts mechanical energy into electrical energy for the propulsion system.
2nd-generation High-Temperature Superconducting (HTS) wire High performing HTS wire (coated conductors), based on YBCO (yttrium barium copper oxide) thin film, deposited on a steel tape. It differs from the 1st generation HTS wire tape, which is based on ceramic Bi-Sr-Ca-Cu-O filaments in a silver matrix.
4QCSingle phase AC/DC converter capable of 4 quadrant operation (current, voltage).
Absorption It refers to absorption of particles of gas or liquid in liquid or solid material.
Absorption chillerSee Absorption Refrigerator.
Absorption circuit Resonant circuit that acts as a short circuit for a certain frequency that is to be eliminated in current.
Absorption refrigeratorRefrigerator that uses a heat source (e.g., solar, kerosene-fueled flame) to provide the energy needed to drive the cooling system.
ACAir conditioning is the dehumidification of indoor air for thermal comfort. In a broader sense, the term can refer to any form of cooling, heating, ventilation, or disinfection that modifies the condition of air. An air conditioner (often referred to as AC or air con.) is an appliance, system, or machine designed to stabilise the air temperature and humidity within an area (used for cooling as well as heating depending on the air properties at a given time), typically using a refrigeration cycle but sometimes using evaporation, commonly for comfort cooling in buildings and motor vehicles.
ACAlternating Current: a continuous electric current that periodically reverses direction, usually sinusoidally.
AC-linkTransformer's leakage inductance and resonant capacitor composing a resonant circuit interfacing 2 converters, where current and voltage have AC characteristics.
All-out runningProcedure consiting in using the maximum of the available effort to carry out the trip. It’s the traction mode which gives the smallest running time.
APRPreliminary Risk Analysis: process of defining and analyzing the dangers associated to a system.
ATOAutomated Train Operation: system ensuring partial or complete automatic train piloting and driverless functions.
ATPAutomated Train Protection: protection system installed in some trains in order to help prevent collisions through a driver's failure to observe a signal or speed restriction.
ATSAutotransformer Stations
AUXAuxiliaries: summary of all consumers in a train not related to the traction, e.g heating & ventilation or light.
BMIBattery Management with Interface: supervision system for Battery cells or systems, taking care of voltage and temperature values. Communication with superior control functions via interface possible.
BMSBattery Management System: electronic device that manages a rechargeable battery (cell or battery pack), such as by monitoring its state, calculating secondary data, reporting those data, protecting it, controlling its environment, and / or balancing it.
BogieAssembly composed by at least two wheelsets and a suspension system (elastic and damping elements) between wheelsets and bogie frame and bogie frame and carbody. It can support traction drives as well (powered bogie).
Booster modeOperation principle applied when using onboard energy storage for additional power for a diesel electric vehicle.
BTMSBattery Thermal Management System: device ensuring stable cooling conditions for the battery system by ether cooling during summer or heating during winter.
CEERCouncil of European Energy Regulators: "not-for-profit" organisation in which Europe’s national regulators of electricity and gas voluntarily cooperate to protect consumer' interests and to facilitate the creation of a single, competitive and sustainable internal market for gas and electricity in Europe.
CENELECEuropean Committee for Electrotechnical Standardisation: its mission is to prepare voluntary electrotechnical standards that help develop the Single European Market/European Economic Area for electrical and electronic goods and services removing barriers to trade, creating new markets and cutting compliance costs.
ChokeDevice composed by an inductuctivity in a circuit, used to block higher frequency signals.
ChopperComponent used to control the energy flow between the energy storage and the DC-Link.
Clausius-Rankine-process Thermodynamic cycle which converts heat into work. The heat is supplied externally to a closed loop, which usually uses water as the working fluid.
CLDMComponent Losses Dependence Matrix: A matrix providing the qualitative and quantitative description of all the losses contributions within a component, used to identify the minimum set of interface parameters for the NRG model of the component.
Coasting runningVehicle driving mode through the effect of inertia, consisting to stop the traction effort when the speed limit is reached. The resumption of traction is carried out when the speed loss due to the coasting running reaches a certain value set by the driver.
Cold loss Loss source occuring in cold part of superconducting devices. In transformers it is mainly due to AC-field components, inducing several types of magnetic, hysteretic and eddy current loss in the conductor tape. Can be removed by using cryogenic cooling systems.
Cold platesPlates used to cool semiconductors and resistors suitable for employment with a proper cooling fluid. They include copper or stainless steel tubed cold plates pressed into a channeled aluminium extrusion, and vacuum-brazed fin cold plates consisting of two plates metallurgically bonded toghether with internal fin.
ConverterElectronic device which converts electrical power, consisting of power and information electronic devices plus electrical hardware (e.g. switches).
Cooling systemFor the superconducting traction transformer a cooling system is required to generate operation temperatures below the critical temperature Tc. Tc is the critical temperature, at which the transition from normal conducting (R>0) to superconducting (R=0) occurs.
Cooling towerAssembly mainly containing radiators, motor-fan and expansion tanks, used to cool power converters, transformer and braking rheostat.
COPCoefficient Of Performance: in thermodynamics, the ratio of the output heat of a pump to the supplied work.
CPUControl Processing Unit
Critical currentA current threshold in the superconducting wire below the current transport is virtually lossless. Ic increases with decreasing magnetic fields and temperature.
CryocoolerMachine that removes heat from a low temperature niveau to room temperature via a reciprocating vapor-compression/expansion cycle in a working gas.
CryostatEnclosure vessel positioned around cold cryogenic equipment to minimze heat input through walls.Is double walled with vacuum in between.
Current leadElectrical connection between environment and cold part of superconducting device.
CVConverter
DASDriver Assistance System: system giving recommendations to the train driver, helping to conduct a train task in time with minimum energy consumption. DAS consists of a wayside TCC and an onboard unit. An implementation is described in Railenergy WP 2.3 as EETROP Driver.
DCDirect Current: unidirectional flow of electric charge.
DC linkDirect Current connection (bus) between inverters.
DC/DC converterConverter interfacing two Direct Current (DC) grids.
DDLLine Fault
DEMUDiesel Electric Multiple Unit: diesel multiple unit for passenger transport (propulsion system between diesel engine and wheelset is based on electrical energy).
Desorption Phenomenon whereby a substance is released from or through a surface. The process is the opposite of sorption (that is, adsorption and absorption). This occurs in a system being in the state of sorption equilibrium between bulk phase (fluid, i.e. gas or liquid solution) and an adsorbing surface (solid or boundary separating two fluids). When the concentration (or pressure) of substance in the bulk phase is lowered, some of the sorbed substance changes to the bulk state.
Direct driveA drive system which transmites the toque direct to the wheel axle shaft without a gear unit.
DLCDouble Layer Capacitor: electrochemical capacitors that have an unusually high energy density when compared to common capacitors, typically on the order of thousands of times greater than a high capacity electrolytic capacitor.
DMIDriver Machine Interface: MMI designed for railway application.
DMUDiesel Multiple Unit: diesel multiple unit for passenger transport which is powered by on-board diesel engines.
DODDate of death, lifetime
DSDemonstration Scene (in short: demo scene): it is a collection of Use Cases, and specify a particular grouping of technical and operational data each representing an essential and typical part of European railway traffic.
DSMDriving Style Manager: synonym for DAS.
Dual system operationSystem operating at 15kV/16.7Hz or 25kV/50Hz.
ECTSEuropean Train Control System: a subset of ERTMS providing a level of protection against over-speed and overrun depending upon the capability of the line side infrastructure. (ERTMS/ETCS terminology)
EDLLine test
EETROPEnergy Efficient Train Operation: it is a term defined by the Railenergy project WP 2.3 for systems working with timetabling and traffic aspects in energy efficient operation. It is divided into EETROP CONTROL and EETROP TIMETABLING.
EETROPEnergy Efficient Train Operation: efficient operation of the railway system is considered as an essential way to energy saving while an efficient management of power level helps to lower the reference subscribed power.
EETROP Timetabling EETROP Timetabling is a system providing energy efficiency to operation of a rail network involving one or several criteria or methods. The basis is a timetable meeting commercial objectives while respecting safety constraints produced manually or by a timetabling tool.
Electrical propulsion systemElectric and mechanical system which converts energy and produces tractive and braking effort between wheel and rail.
EMCElectromagnetic compatibility: it is the branch of electrical sciences which studies the unintentional generation, propagation and reception of electromagnetic energy with reference to the unwanted effects (Electromagnetic interference, or EMI) that such energy may induce.
EMIElectromagnetic Immunity
EMUElectrical Multiple Unit: train configuration with several cars connected and propelled by electric traction.
Energy managementControl element who is organizing the energy flow, part of the energy storage system
Energy modelSystem or subsystem model which describes the power at each input or output port. The model behaves according with static and dynamic parameters (e.g. supply line voltage). The aim of energy model is to be integrated into load flow family simulator, than it should not have any state (i.e. it is simply I/O relation) or energy storage capability.
Energy Service ProfilesEnergy Service Profiles are applicable for the specification and verification of energy consumption of new railway rolling stock, or for the efficiency improvement of existing rolling stock. The criterion for the energy consumption of rolling stock is the total net energy consumed – either at pantograph or from the fuel tank – over a predefined service profile, which is either taken from the future operation of the train, or according to a standardised typical profile valid for the specific service category of trains. Cross reference to TecRec..
Energy storage systemSystem which can store and supply energy from and to the propulsion system e.g. system based onSuperCapacitors, batteries, flywheel.
ERAEuropean Railway Agency: ERA sets standards for European railways. Its mandate is the creation of a competitive European railway area, by increasing cross-border compatibility of national systems, and in parallel ensuring the required level of safety. (Source: Wikipedia)
ERGEGEuropean Regulators Group for Electricity and Gas: it is an advisory group to the European Commission on internal energy market issues in Europe. It was set up by the European Commission to assist the Commission in consolidating a single EU market for electricity and gas. ERGEG’s members are the heads of the national energy regulatory authorities in the EU’s 27 Member States. (Source: Wikipedia)
ERTMSEuropean Railway Traffic Management System: it consists of ETCS and GSM-R (GSM for railway application).
ERTMSEuropean Railway Traffic Management System:it is made up of all the train borne, track side and line side equipment necessary for supervising and controlling, in real-time, the train operation according to the traffic conditions based on the appropriate Level of Application. (ERTMS/ETCS terminology)
ESEnergy Saver: energy storage device to store energy to be reused during acceleration. Could be either Double layer capacitor, battery or flywheel.
ES ModeOperation principle using onboard energy storage for energy saving for a diesel electric vehicle.
ESSEnergy Storage System: system able to store energy for delivery of power at a later stage. Including storage component, control & supervision as well as housing.
ETCSEuropean Train Control System: signalling, control and train protection system designed to replace the many incompatible safety systems currently used by European railways, especially on high-speed lines.
ETRS89European Terrestrial Reference System 1989: ECEF (Earth-Centered, Earth-Fixed) geodetic Cartesian reference frame, in which the Eurasian Plate as a whole is static. The coordinates and maps in Europe based on ETRS89 are not subject to change due to the continental drift.
ETSEU Emissions Trading Scheme: it is a multi-national, emissions trading scheme. ETS currently covers more than 10,000 installations with a net heat excess of 20 MW in the energy and industrial sectors which are collectively responsible for close to half of the EU's emissions of CO2 and 40% of its total greenhouse gas emissions. (Source: Wikipedia)
EVENTThe EVENT project (Evaluation of Energy Efficiency Technologies for Rolling Stock and Train Operation of Railways) was a UIC funded research project aiming at evaluating energy efficient technologies for railway applications, focusing on rolling stock and infrastructure. project duration was 2001-2002. The database was available at www.railway-energy.org and is now part of the Railenergy database. Other relevant projects were PROSPER and REPID.
FEM packagesSoftware for finite element analysis on structural components.
FlywheelRotating energy storage system.
FMECAFailure Modes, Effects and Criticality Analisys: an extension of Failure Mode and Effects Analysis (FMEA), i.e. a a bottom-up, inductive analytical method which may be performed at either the functional or piece-part level. FMECA extends FMEA by including a criticality analysis, which is used to chart the probability of failure modes against the severity of their consequences. The result highlights failure modes with relatively high probability and severity of consequences, allowing remedial effort to be directed where it will produce the greatest value.
Full bridge converterDevice consisting of 2 halfbride configurations, allowing all varieties of operation in single phase systems.
Global ModelThe global model comprises input interface definitions, specification of calculation procedures and output interface definition. It defines a common language, along with a classification, to describe the process of system evaluation. It categorizes input data according to their relevance for the calculation of energy consumption, to give the users an indication on how crucial certain parameters are for achieving meaningful results. The global model is an abstraction layer between
• simulation tools usually used for very detailed engineering studies in industry,
• component modelling and
• evaluation of system efficiency as done in RAILENERGY.
Basically it is a set of rules on how to acquire and store input data and how to organize and aggregate simulation results. Furthermore the global model comprises best practices on the simulation of railway systems. Hence, the global model is a collection of data structures and procedures. The global model mainly is a definition of interfaces and procedures, which are not based on any propritary system environment or implementation method.
GPRSGeneral Packet Radio Service: packet oriented mobile data service available to users of the 2G cellular communication systems global system for mobile communications (GSM), as well as in the 3G systems.
GPSGlobal Positioning System: U.S. based global navigation satellitye system, able to provide reliable information on positioning, navigation and timing.
Gross tkmMore detailed explanation to be provided
Gross tkm hauled
GSMGlobal System for Mobile communications: it is an open, digital cellular technology used for transmitting mobile voice and data services. GSM supports voice calls and data transfer speeds of up to 9.6 kbit/s, together with the transmission of SMS (Short Message Service). GSM operates in the 900MHz and 1.8GHz bands in Europe and the 1.9GHz and 850MHz bands in the US. The 850MHz band is also used for GSM and 3G in Australia, Canada and many South American countries. By having harmonised spectrum across most of the globe, GSM’s international roaming capability allows users to access the same services when travelling abroad as at home. This gives consumers seamless and same number connectivity in more than 218 countries.
GTOGate Turn Off: special type of thyristor, i.e. a high-power semiconductor device. GTOs, as opposed to normal thyristors, are fully controllable switches which can be turned on and off by their third lead, i.e. the so called GATE lead.
Halfbridge converterBasic converter element for 4 quadrant operation; single converter phase made of 2 IGBT and 2 Diodes.
HandlePercentage of requested torque (manipulator position).
Hard switchingOpposite of soft switching.
HeatpipeHeat transfer mechanism to transport large heat at lower temperature difference between hot and cold interface utilizing phase change of heat conductor.
HibernatingParking of trains
HTSHigh Temperature Superconductor: nearly resistance-free conductors made of ceramic materials that exhibit superconducting properties still at 77 K (boiling point of liquid nitrogen). Therefore less expensive cooling systems were needed in comparison to low temperature superconductors (<10 Kelvin). Less power is needed to drive the cryocooler, improves efficiency.
HVHigh Voltage-More detailed explanation to be provided
HVACHeating, Ventilating, and Air Conditioning: the technology of indoor or automotive environmental comfort. HVAC system design is a major subdiscipline of mechanical engineering, based on the principles of thermodynamics, fluid mechanics, and heat transfer.
Hybrid energy storageEnergy storage system comprising more than one energy storage element (e.g. combinatioon of battery and supercap)
Hybrid propulsion systemPropulsion system with at least two independed energy sources (e.g. diesel engine and energy storage system).
ICE3High-speed train operated by Deutsche Bahn.
IGBTInsulated Gate Bipolarized Transistor: a three-terminal power semiconductor device, noted for high efficiency and fast switching.
IMInfrastructure Manager: it is a common abbreviation for "Infrastructure Manager" - companies which are responsible for the railway infrastructure (tracks, lines, catenary system, substations depots, stations, bridges, tunnels etc.), their maintanence and building. Due to the ongoing liberalisation of the European railway markets national railway companies are being divided into IMs and railway operating companies (see RU). Other stakeholders in the railway system and market are RUs, PTAs, SIs. Relevant industry association: www.uic.org
InterCity (long distance) servicePassenger transport between urban areas (cities) with typical stopping distances in an range from 30 to 150 km.
InverterPart of converter which converts electrical power from DC to AC (single or multiple phases) with flexible frequency and voltage and reverse.
IPProtection Index: shows the protection rate for a device from external agents. It is made of 2 digits prefixed by IP: the first digit represents the degree of protection against solid objects and dust; the second represents the degree of protection against liquids.
KPIKey Performance Indicators are used in the framework of the Railenergy project to determine and describe the energy performance of railway related technologies. A detailed definition and description of KPIs can be found in the document xxx.
K-valueProperty of a material that indicates its ability to conduct heat
LCCLife Cycle Cost: total cost of ownership over the life of an asset.
Li-IonenLithium Ion Battery type usable for energy storage
LN2Liquid nitrogen.
Load factor
LRTLight Rail Transit: form of urban rail public transportation that generally has a lower capacity and lower speed than heavy rail and metro systems, but higher capacity and higher speed than traditional street-running tram systems. The term is typically used to refer to rail systems with rapid transit-style features.
LRULine Replacable Unit
LTALong term agreements
LV Low Voltage
MCGMobile Communication Gateway for train to ground communication
MMIMan Machine Interface: it is the system by which people (man) interact with a machine. The man machine interface includes hardware (physical) and software (logical) components. man machine interfaces exist for various systems, and provide a means of: Input, allowing the users to manipulate a system, and/or Output, allowing the system to indicate the effects of the users' manipulation.
Model layerEnergy model variables can be grouped in layers, which summarise model behaviour with respect to functional aspects (e.g. energy, interface variables, control and management).
ModulesMechanical box containing electronic devices and relative cooling system to realize an electric apparatus (inverter, chopper, braking).
MTBFMean Time Between Failures: predicted elapsed time during two consecutive failures of a system or component during operation.
MTTRMean Time to Repair: average time required to repaire a failed component or device.
MUMultiple Unit
Multi system operationVehicules adaptable to different grids (15kV/16.7Hz, 25kV/50Hz, 3kVdc, 1.5kVdc).
Multiple transformer conceptSeveral transformers each with one individual core transferring power in parallel (secondary windings on same, primary windings on different potential).
MV loadsMedium voltage loads, for example pump and motor-fan supplied by auxiliary converter to 380/450 V.
MVBMultifunction Vehicle Bus: it is a field bus, consisting of a single or dual data line used in train control systems, and described in IEC 61375.
NHE moduleSpecific Battery type dedicated for energy storage (typically NiMH technology).
NHP moduleSpecific Battery type dedicated for power supply (typically NiMH technology).
NiMHNickel Metal Hydid battery type usable for energy storage
NRESSNordic Railway Energy Settlement System: part of ERESS (European Railway Energy Settlement System). The aim is to provide a simple, efficient, reliable, accurate and flexible energy settlement system both for the current rail market and the future market where most trains will be equipped with meters and many different train operators will use the railways. www.eress.eu (Source: ERESS)
NRG modelDescription of the behavior of a component or subsystem with respect to power/energy flows through it. The description is given according to a predefined set of parameters (interface parameters) affecting the input/ouput relationships. The set of interface parameters and of the I/O relationships for the NRG model of each component is defined at WP/SP level in order to fulfill the needs of SP analysis. The NRG model may be given as a set of equations with input and interface parameters as variables, one or more multidimentional data tables, graphs or any other data representation form agreed among the users of the NRG model.
N-x redundancyAt least N-x subcomponents required (e.g. to meet the voltage or power requirements), while N installed and intact subcomponents can share the demands. x faulty subcomponents don't make the total component fail, but x+1.
OCLOverhead Contact Line
Passenger km
Passenger transport on regional linesPassenger transport outside of pure urban areas with typical stopping distances in an range from 3 to 10 km.
PCCControl Center
PCSPassenger Counting System: it is counting the number of people entering or leaving a train.
PISPassenger Information System: electronic system which provides real-time information to passengers.
PLCProgrammable Logic Controller: digital computer used for automation of electromechanical processes.
PMAbbreviation for Permanent Magnet excitation In a PM-motor the the magnetic field is exictated by permanent magnets.
PROSPERThe PROSPER project (Procedures for Rolling Stock Procurement with Environmental Requirements phase II) aimed at establishing a common framework for tendering and purchasing railway rolling stock taking into account the einvironmental performance of rolling stock (noise, diesel exhaust emissions, recycling, waste and energy efficiency. The UIC funded project (2002-2005) resulted in the UIC leaflet 345 "Environmental Specifications for new rolling stock" . More information: www.railway-procurement.org. See also REPID and EVENT.
PSOPublic Service Obligation: in transport, public service obligation or PSO is an arrangement in which a governing body or other authority offers an auction for subsidies, permit the winning company a monopoly to operate a specified service of public transport for a specified period of time for the given subsidy. This is done in cases where there is not enough revenue for routes to be profitable in a free market, but where there is a socially desirable advantage in this transport being available. The use of PSO can be applied to many mode of transport, including air, sea, road or rail. (Source: Wikipedia)
PTAPublic Transport Authorities: it is common abbreviation for "Public Transport Authorities" (also: Organising Authorities - OA). PTAs are public or publicly-owned organisation with legal responsibilities to regulate, plan and commission/assign public transport services in a specified geographic area. Other stakeholders in the railway system and market are IMs, RUs, SIs.
PWMPulse Witdth Modulation: involves the modulation of its duty cycle to control the amount of power sent to a load and its harmonic content.
RailisaRailisa is the official UIC statistics database where member companies report on a yearly basis relevant figures of their operational business.
RCResistor Capacitor
Redundancy conceptConcept allowing further operation at single or multiple faults depending on type of redundancy.
RefrigerantCompound used in a heat cycle that reversibly undergoes a phase change from a gas to a liquid.
REPIDREPID (Rail sector framework and tools for standardising and improving usability of Environmental Performance Indicators and Data formats) was an UIC funded project (2002-2005). More information: www.railway-procurement.org. See also PROSPER and EVENT.
Roebel barParallel and cabled arrangement of superconducting tapes for larger current carrying capacity.
RPBRailenergy Performance Baseline
RRGRailenergy Requirements Baseline
RURailway Undertaking Company: it is common abbreviation for "Railway Undertakers" or "Railway Undertaking Companies" (also: "Railway Operators") - companies which operate railway vehicles and offer railway transport services (freight and/or passenger). Due to the ongoing liberalisation of the European railway markets national railway companies are being divided into RUs and Infrastructure Managers (see IM). Other stakeholders in the railway system and market are IMs, PTAs, SIs. Relevant industry association: www.uic.org
SCADASupervision Control & Data Acquisition system
Seat km
Self ventilationAir cooling system with a fan driven by the rotor shaft of the electrical machine.
Series resonant circuitSeries connection of capacitance and inductance.
Series resonant converterDC/DC converter used in resonant operation to reduce switching loss.
Short circuit voltage ukApplied primary voltage when nominal current flows in shorted secondary winding, divided by nominal voltage.
Short circuiting contactorContactor to short-circuit a converter in case of a converter fault.
SISystem Integrator: it is common abbreviation for "System Integrators" - companies which build and sell major and main railway technical systems, such as locomotives, waggons, multiple units, signaling systems, energy supply systems (e.g. substations). They integrate own and suppliers' components and sub-systems to final complex products. Other stakeholders in the railway system and market are IMs, PTAs, RUs. Relevant industry association: www.unife.be
Single transformer conceptOne single transformer with several windings mounted on one common core transferring power in parallel (secondary windings on same, primary windings on different potential).
SLDMSubsystem Losses Dependance Matrix: a CLDM where the component is actually a subsystem consisting of various components. SLDM can also be obtained merging the CLDMs of the subsystem's components.
Soft switchingConverter switching at zero current, voltage or both (see ZCS,ZVS).
SolventLiquid, solid, or gas that dissolves another solid, liquid, or gaseous solute, resulting in a solution.The most common solvent is water.
SRSSystem Requirement Specification: document that defines the system level requirements for and within a system.
SSTSubstation
Standard operational profile
Standard service profileDriving profile for a train in a given service type e.g. high-speed operation
Stirling coolerA Stirling engine is a thermal engine that operates by cyclic compression and expansion of a working gas, e.g. Helium. Cooling is achieved by expansion of the working fluid. In refrigerator mode the Stirling is driven by an electric drive.
Stray fieldMagnetic field between primary and secondary transformer windings. Magnetic flux in stray field gap contributes to short circuit voltage.
STTSThe STTS (Superconducting Traction Transformer System) has high-temperature superconducting (HTS) windings and secondary chokes. It also includes the required integrated cooling system.
SupercapDouble layer capacitor usable for energy storage
TCCTrain Control Centre: it is a wayside application, providing data and train-to-wayside communication for the operation of trains.
TCNTrain Communication Network: it is a hierarchical system of field busses for railway application. It is used to exchange process data and message data. TCN is being described with IEC 61375.
TENTrans-European Transport Network: a planned set road, rail, air and water transport networks designed to serve the entire continent of Europe. The TEN-T networks are part of a wider system of Trans-European Networks, including a telecommunications network and a proposed energy network.
Timetable A timetable is the description of all train movements (journeys) and all temporary restrictions which are planned for a given operational day. It contains all description of train journeys following imposed routes, under the form of a planned arrival time to and a departure time from each station.
TPSTraction Power (supply) Substations
Traction drive Traction motor plus mechanical transmission system between motor and wheelset.
Traction motorDevice which converts electrical energy into mechanical energy for the propulsion system and reverse when braking.
TRAINERTRAining programmes to Increase Energy-efficiency by Railways, www.iee-trainer.eu
TSITechnical Specification for Interoperability: specifications drafted by the European Railway Agency and adopted in a Decision by the European Commission, to ensure the interoperability of the trans-European rail system.
TSOTransmission Service Operators: it provides open-access transmission service and monitors the high voltage transmission system throughout agiven area or region.
UCUse Case: in the scope of Railenergy, Use Cases are coherent (national) subsets of framework parameters. Each use case represents a fixed topography, railway technologies and operation. The starting and border station for each line are defined, and the rolling stock operating on the line are identified.
UICInternational Union of Railways, Union internationale des chemins de fer
UNIFEProfessional association for the railway supply industry, directly and through national associations representing over 900 European companies. (adding reference to UIC if needed)
Water jacket coolingWater cooling system wrapped around thze housing of an electrical machine e.g. traction motor.
WGS84World Geodetic System 1984: standard for use in cartography, geodesy, and navigation. It comprises a standard coordinate frame for the Earth, a standard spheroidal reference surface (the datum or reference ellipsoid) for raw altitude data, and a gravitational equipotential surface (the geoid) that defines the nominal sea level.
WheelsetSet of wheels plus shaft for rail vehicle.
ZCSOperating mode where the power semiconductor is turned- on or -off at zero current. Thus the forward voltage transition ideally avoids losses in the device.
ZVSOperating mode where the power semiconductor is turned- on or -off at zero voltage. Thus the forward current transition ideally avoids losses in the device as far as possible.